Table of Content
Verify that the supply voltage is correct. Connect fixture to a 120 volt, 60 Hz power source. More often that you’d imagine, the simple question “what is a smart home?
The light fixture is on the same circuit as a motor, transformer, or fluorescent bulb. The circuit wiring is incorrect, if this is a new installation. Longer lifetime – Solid State lighting has no filament to break. During MANUAL MODE, by switching the main switch OFF over 30 seconds then back ON again, the PIR sensor will reset to the “warm-up” period. You may adjust the sensor left and right or up and down to get the desired lamp direction. Adjusting the Lamp heads and SensorLamp heads can be adjusted easily.
Motion Sensor Light: 5000K 3-Head Security Light
Slide the “LUX” switch toward the “ ” position to turn on in sunset or in darkness. The higher the “ SENS” setting , the greater the possibility of false triggering. To reduce false triggering, slide the “SENS” switch toward the “ ” setting if you don’t need long detection distance while using this light. Slide the “LUX” switch toward the “ ” position to turn on in darkness. Slide the “ SENS” switch toward the “ ” position for long detection range. Slide the “ SENS” switch toward the “ ” position for middle detection range.
This device must accept any interference received, including interference that may cause undesired operation. I've used several night lights, but this is the best yet. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Reposition the bulb away from the detector or nearby objects. ProblemPossible CauseSolutionThe light will not come on.The light switch is turned off.
Home Zone Security LED Light Motion Activated 710080
Place the mounting plate against the junction box.When mounting to a wall, the “UP” arrow must point upward. Mount motion sensor so motion moves across detection zone. Electrostatic Discharge can cause damage to LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This setting is used to control the time span of how long the light remains on when motion is detected. Set the “ ” switch to the 1, 3, 7 minutes position. The security light will stay on as long as motion is detected and will go off after the time span you set after no motion is detected. Set the switch to the 1, 3, 7 minutes position. Insert the small mounting bolt through the mounting plate hole and mounting bracket hole.
The Bright Way to do Home Security
This fixture is intended to be connected to a properly installed and grounded UL listed junction box. Why Outdoor Lighting Is Important Outdoor lighting for your home is an incredibly important part of home security and home aesthetics. If you are ready to look at outdoor lighting options, we’re glad you came across our article! Gently grasp the motion sensor and adjust the sensor left and right or up and down to get the desired lamp direction. Connecting the positioning hole of the light fixture and positioning pillar of the mounting plate . • Insert the small mounting bolt through the mounting plate hole and mounting bracket hole.
Do not use a dimmer or timer to control the light fixture. Replace the dimmer or timer with a standard on/off wall switch. They will be grouped as an invisible system and working together.
If you are unsure about the installation or maintenance of this fixture, consult a qualified, licensed electrician. Before installing, servicing or performing routine maintenance upon this equipment, follow these general precautions. Upgrade your home with the beautiful crackle glass solar path lights from Home Zone Security. Equipped with long lasting LED lights and an attracti... Upgrade your deck and yard with decorative post cap lights from Home Zone Security. Equipped with warm color temperature long-lasting LED lights an...
You can set the light to motion activated which I think is generally the main reason people buy these lights or you can manually override it. The slide toward the ” ” position for a long detection range ( 3-70 ft). The slide toward the ” ” position for the middle detection range ( 3-49 ft). The slide toward the position for a short detection range (3-30 ft). • Push the decorative rubber cover firmly into the large mounting bolt hole on the light fixture . 21.3 m / 70 ft detection range based on ambient temperature 25 Celsius degree.Adjust the sensor head horizontal for long coverage.
Position the lamp head in the general direction of the desired light coverage. LED products are Polarity Sensitive. Ensure proper polarity before installation.
The simple answer is that a smart home is a house that is equipped with various devices which...
Wear gloves and safety glasses at all times when removing fixture from carton, installing, servicing or performing maintenance. Increase Home Security with Lighting Home security will always be a hot topic for homeowners. Burglars are always coming up with new ways to work their way into your home, and more often than not, lighting is often overlooked by... Upgrade your home garden landscape with decorative solar pathway lights from Home Zone Security. Equipped with long lasting LED lights and elegant ... Swing the lamp heads to adjust the lamp head left and right or up and down to get the desired lamp direction.
Living in Alaska in the winter we have plenty of darkness. This security light is an excellent choice for the dark nights in winter. It is very bright and only activates after dark. Push the rubber plug firmly into the large mounting bolt hole on the light fixture . When installing the mounting plate to a wall, the “arrow” must be upward.
Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply. Replace the dimmer or timer with a standard on/off wallswitch. The light comes on for no apparent reasonThe motion sensor may be sensing small animals or automobile traffic. Adjust the Ambient Light level setting to “MOON” position. The light comes on during the day.The detector may be installed in a relatively dark location. The light fixture is not properly attached to the mounting plate, if this is a new installation .
No comments:
Post a Comment